2000系列微差壓力表
2000 Series Micro-Differential Pressure Meter
2000系列微差壓力表產品簡介
2000系列微差壓表廣泛適用于監測潔凈室正負壓、差壓、過濾器前后差壓、爐膛負壓、風扇和鼓風機壓力，同時可用于燃燒過程中的空氣煤氣比質控制及自動閥控制。
Brief introduction:
2000 series micro-differential pressure meters are widely used in monitoring positive or negative pressure of clean room, differential pressure, differential pressures between filter, negative pressure of hearth, pressures of fan or blowing machine, etc. In addition, it can also be used for the quality control of air-gas proportion in combustion process and control of automatic valves.
主要技術參數
精確度：在21℃以下為±2%FS
使用環境溫度：-7℃～60℃
額定壓力：-68～103kPa
過壓：約172Kpa時橡膠過壓塞被沖開
過程連接：高壓和孔低壓均為1/8″錐管螺紋，兩組（側面和背面各一組）
外殼材質：壓膜鑄鋁
標準附件：2個1/8″NPT堵頭，2個1/8″螺紋橡膠管接頭，3個安裝螺絲卡
安裝方式：有三種安裝方式嵌入、表面、管道式。
Principal technical parameters:
Accuracy: ±2%FS below 21℃
Ambient temperature in use: -7oC 60oC
Rated pressure: approximay -68～103kPa
Overpressure: overpressure plug bursts at 172kPa approximay.
Process connection: 1/8” tager pipe thread is used for high pressure and hole low pressure, in two groups （each group for side and back） with shell made of: squeeze film cast aluminum.
Standard accessories: 2 1/8″NPT end caps, 2 1/8″rubber pipe fittings with thread grinding, 3 clips for installation screw
標度范圍 Measuring ranges
| 型號 | 標度范圍 | 精確度等級 | |
| 2000 | 0～60；0～125；0～250（Pa） | 0～0.5；0～1；0～1.5；0～2；0～3；0～4；0～5；0～8；0～10；0～15；0～20；0～25；0～30（kPa） | 2 |
外形尺寸 External dimension
差壓系列儀表選型指南
Guide for type selection of Micro-Differential Pressure
Meter series instruments and meters
| 產品電腦編碼 | 型號 | 產品名稱 |
| 1500103713 | | 2000系列微差壓表 |
訂貨須知 Ordering instructions
訂貨時須注明：產品電腦編碼、型號、名稱、精確度、測量范圍。如特殊要求，請注明技術要求。
Ordering instructions: The product computer code ,types, names, accuracy grades, and measuring ranges .must be clearly noted. In case of special requirements, technical requirements shall be clearly noted specifications on the back of the order on ordering goods.
