吸附式干燥機

◆產品特點 Product features

※具有穩定一致的出氣壓力和露點

1.吸附塔之高度與直徑經實驗結果精密計算,塔床阻力小,保證了壓縮氣體干燥劑5秒的接觸時間,滿足成品氣的露點要求。

2.30%的干燥劑余量,用于補償干燥劑的自然老化,確保干燥。

3.大型擴散器,確保氣流均勻通過干燥劑層,消除溝流現象。

※再生氣量損耗小于14%

1.的機筒設計,保存99%的吸附熱量,儲存的熱量用于增加再生階段的再生氣溫度,提高設備的解吸能力,使得再生更。

2.干燥和再生采用反向?qū)α鞣桨?濕空氣流過干的吸附劑時。再生氣出口含濕量控制在亞飽和狀態,使消聲器及排氣通道無結露之慮。

3.可根據干燥機的運行負載需求調節再生氣用量,確保再生氣流連續穩定,再生壓力低至臨界。

※干燥劑使用壽命長

1.合適的機筒尺寸,使氣體通過干燥劑層的流速和時間保持狀態,充分發揮干燥劑的性能。

2.合理的系統配置,在氣流進入機筒前,經高效除油處理及時清除氣流中內含油物與重污染物,避免干燥劑層受污染。

※設備采用了新穎高品質電動及氣動閥和可靠的全電子可編程序控制器,人機界面友好,自動連續顯示雙塔工況,循環周期現場可編,出廠設定10min。閥門壽命長達50萬次動作。

※筒體內壁作冷鍍鋅防銹處理,10年不銹蝕。

※動作準確、性能穩定、操作簡便,安裝無需基礎。

※Bend it out on the same has the stable  pressure and dew point

1. The height and diameter  adsorption tower by the experimental results calculated precisely, tower, ensure  the small resistance bed compressed gas desiccant 5 seconds contact time, meet  the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant  used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform  through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14%  renewable

1. Excellent barrel design, save  99% of the adsorption quantity of heat, storage quantity of heat is used to  increase the regeneration stage again angry temperature, improve equipment  desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the  reverse convection scheme, wet air through the dry when the adsorbent best  effect. Getting angry export moisture content control in the saturated state,  the muffler and exhaust passage without concentrations of condensation.  

3. According to the operation of  the dryer load demａnd adjust dosage, ensure again angry for stability,  regeneration renewable air pressure low to critical.

※Bend desiccant long service life  

1. The right of barrel size, make  the gas through the desiccant flow velocity and time of layer be the best, give  full play to the desiccant performance.

2. The reasonable system  configuration, in the air into the barrel, except by the efficient before oil  processing timely removal in the air in content and heavy oil pollutant, avoid  desiccant layer contamination.

※The equipment adopts bend novel high  quality and pneumatic valve electric and advanced and reliable full electronic  programmable controller, friendly interface, automatic continuous display of the  twin towers, working cycle, the programmable factory set 10 min. The valve life  for 500000 times action.

※Bend the cylinder body wall be cold  galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance,  accurate, easy operation and installation with no need of  foundation.

◆主要技術參數 Main technical  parameters