中文版本： 一般廠家都是通過物流發給用戶，首先要廠家對產品外部包裝是怎樣處理的，有的廠家為了賺取跟多的利潤，用紙箱包裝，用紙箱包裝的損壞率肯定是偏高的，是木箱包裝是比較好的，因?yàn)槲锪鞴镜墓と四苡心敲葱⌒囊硪韱幔克詣衲承S家萬不要撿了芝麻，丟了西瓜。 接下來說技術處理這塊：磁翻板液位計浮子在運輸過程中為了不使浮子組件損壞，故出廠前將浮子組件取出液位計主體管外，待液位計安裝完畢后，打開底部排污法蘭，再將浮子組件重新裝入主體管內，注意浮子組件重的一頭朝上，不能倒裝。如果在出廠時已經將浮子組件安裝在主體管內，為保證運輸過程中不使浮球組件損壞，我們用軟卡將浮子組件固定在主體管內，安裝時只要將軟卡抽出即可。先與其他液位計進行對照,再用磁鐵進行吸浮子來判斷液位,磁翻板液位計,一般出現測量不準為浮子或筒體有雜質吸附上造成,再者被測液體密度出現變化。盡量不讓桶內的介質汽化。一般拌熱就可以了。磁翻板液位計的伴熱,采用半伴熱,保溫一般用DN50的巖面管開口只漏出面板即可,用油氈紙?jiān)诎?外面刷一層漆將玻璃絲布粘上,再刷一邊漆即可。工藝懷疑不準的時候，首先和玻璃板液位計對照，然后是像觀察玻璃板一樣排放磁浮子內液體?？船F(xiàn)場和遠傳信號是否一樣，逐一判斷問題在那里。拌熱要根據當?shù)貧鉁睾徒橘|(zhì)性質來做。 只有抓住更多的細節，做好每一點，磁翻板液位計在運輸過程中損壞率肯定是很低的！！
英文版本：
General manufacturers are through the logistics to the user, first of all to manufacturers of the product packaging is how external processing, some manufacturers in order to earn more profits, packing in cartons, carton packaging for damage rate is high, it is best to wooden box packaging is better, because the logistics company to do so with great care workers? So that some manufacturers do not pick up the sesame, lost watermelon. Then, the technology of processing: magnetic level gauge float in the transport process in order not to make the floater component damage, so the factory will float assembly extraction liquid level gauge body tube for liquid level meter, after installation, open the bottom discharge flange, the float assembly back into the main tube, pay attention to a head float assembly of heavy, not flip. If in the factory will have a float assembly is installed in the main tube, in order to ensure the transport process does not make the ball float component damage, we use soft card will float assembly is fixed in the main tube, when installed as long as the soft card out. First, compared with other liquid level meter, .and then the magnetic suction float to judge the level, magnetic level gauge, generally appear to float or inaccurate measurement of cylinder body are caused by adsorption of impurities, and the measured liquid density change. Try not to let the evaporation of the medium in the barrel. General mixed hot can. Magnetic level gauge with hot plate, a heat insulation adopts, general use DN50 rock surface tube opening panel can only escape, with asphalt felt paper in the package outside a coat of paint, glass cloth adhesive on the side, then brush the paint can be. Process that no time, the first and the glass plate level control, and then discharge liquid magnetic floater like glass plate. Look at the site and remote signal is the same, one by one judge problem. Mix according to the local temperature and dielectric properties to do. Only to seize more details, do a good job in every point, magnetic level gauge damage during transport rate is very low!!
會員1.png)