激情综合啪啪6月丁香,久久久久国产精品91福利,99精品日韩欧美在线观看,91成人午夜福利在线观看国产

行業產品

  • 行業產品

上海湘杰儀器儀表科技有限公司


當前位置:上海湘杰儀器儀表科技有限公司>資料下載>湘杰儀器提供D882-02塑料薄板材抗拉特性的試驗方法

    暫無信息

經營模式:生產廠家

商鋪產品:203條

所在地區:上海

聯系人:李先生 (經理)

資料下載

湘杰儀器提供D882-02塑料薄板材抗拉特性的試驗方法

閱讀:924發布時間:2009-07-30

  • 提供商

    上海湘杰儀器儀表科技有限公司

  • 資料大小

    0K

  • 資料圖片

    查看

  • 下載次數

    0次

  • 資料類型

  • 瀏覽次數

    924次

  • 免費下載


塑料拉力機;塑料拉力機維修;塑料拉力機報價

唐:

Standard Test Method for
Tensile Properties of Thin Plastic Sheeting1
This standard is issued under the fixed designation D 882; the number immediay following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
These test methods have been approved for use by agencies of the Department of Defense to replace Method 1013 of Federal Test
Method Standard 406.
1. Scope *
1.1 This test method covers the determination of tensile
properties of plastics in the form of thin sheeting, including
film (less than 1.0 mm (0.04 in.) in thickness).
NOTE 1—Film has been arbitrarily defined as sheeting having nominal
thickness not greater than 0.25 mm (0.010 in.).
NOTE 2—Tensile properties of plastics 1.0 mm (0.04 in.) or greater in
thickness shall be determined according to Test Method D 638.
1.2 This test method may be used to test all plastics within
the thickness range described and the capacity of the machine
employed.
1.2.1 Static Weighing, Constant-Rate-of-Grip Separation
Test—This test method employs a constant rate of separation of
the grips holding the ends of the test specimen.
1.3 Specimen extension may be measured in these test
methods by grip separation, extension indicators, or displacement
of gage marks.
1.4 A procedure for determining the tensile modulus of
elasticity is included at one strain rate.
NOTE 3—The modulus determination is generally based on the use of
grip separation as a measure of extension; however, the desirability of
using extensometers, as described in 5.2, is recognized and provision for
the use of such instrumentation is incorporated in the procedure.
1.5 Test data obtained by this test method is relevant and
appropriate for use in engineering design.
1.6 The values stated in SI units are to be regarded as the
standard. The values in parentheses are provided for information
only.
1.7 This standard does not purport to address all of the
safety concerns, if any, associated with its use. It is the
responsibility of the user of this standard to establish appropriate
safety and health practices and determine the applicability
of regulatory limitations prior to use.
NOTE 4—This test method is similar to ISO 527-3, but is not considered
technically equivalent. ISO 527-3 allows for additional specimen configurations,
specifies different test speeds, and requires an extensometer or
gage marks on the specimen.
2. Referenced Documents
2.1 ASTM Standards:
D 618 Practice for Conditioning Plastics for Testing2
D 638 Test Method for Tensile Properties of Plastics2
D 4000 Classification System for Specifying Plastic Materials3
D 5947 Test Methods for Physical Dimensions of Solid
Plastic Specimens4
D 6287 Practice for Cutting Film and Sheeting Test Specimens4
E 4 Practices for Force Verification of Testing Machines5
E 691 Practice for Conducting an Interlaboratory Study to
Determine the Precision of a Test Method6
2.2 ISO Standard:
ISO 527-3 Plastics—Determination of Tensile Properties—
Part 3: Test Conditions for Films and Sheets7
3. Terminology
3.1 Definitions—Definitions of terms and symbols relating
to tension testing of plastics appear in the Annex to Test
Method D 638.
3.1.1 line grips—grips having faces designed to concentrate
the entire gripping force along a single line perpendicular to the
direction of testing stress. This is usually done by combining
one standard flat face and an opposing face from which
protrudes a half-round.
3.1.2 tear failure—a tensile failure characterized by fracture
initiating at one edge of the specimen and progressing across
the specimen at a rate slow enough to produce an anomalous
load-deformation curve.
4. Significance and Use
4.1 Tensile properties determined by this test method are of
1 These test methods are under the jurisdiction of ASTM Committee D20 on
Plastics and are the direct responsibility of Subcommittee D20.10 on Mechanical
Properties.
Current edition approved April 10, 2002. Published June 2002. Originally
published as D 882 – 46 T. Last previous edition D 882 – 01.
2 Annual Book of ASTM Standards, Vol 08.01.
3 Annual Book of ASTM Standards, Vol 08.02.
4 Annual Book of ASTM Standards, Vol 08.03.
5 Annual Book of ASTM Standards, Vol 03.01.
6 Annual Book of ASTM Standards, Vol 14.02.
7 Available from American National Standards Institute, 25 W. 43rd St., 4th
Floor, New York, NY 10036.
1
*A Summary of Changes section appears at the end of this standard.
Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.
value for the identification and characterization of materials for
control and specification purposes. Tensile properties may vary
with specimen thickness, method of preparation, speed of
testing, type of grips used, and manner of measuring extension.
Consequently, where precise comparative results are desired,
these factors must be carefully controlled. This test method
shall be used for referee purposes, unless otherwise indicated
in particular material specifications. For many materials, there
may be a specification that requires the use of this test method,
but with some procedural modifications that take precedence
when adhering to the specification. Therefore, it is advisable to
refer to that material specification before using this test
method. Table 1 in Classification D 4000 lists the ASTM
materials standards that currently exist.
4.2 Tensile properties may be utilized to provide data for
research and development and engineering design as well as
quality control and specification. However, data from such
tests cannot be considered significant for applications differing
widely from the load-time scale of the test employed.
4.3 The tensile modulus of elasticity is an index of the
stiffness of thin plastic sheeting. The reproducibility of test
results is good when precise control is maintained over all test
conditions. When different materials are being compared for
stiffness, specimens of identical dimensions must be employed.
4.4 The tensile energy to break (TEB) is the total energy
absorbed per unit volume of the specimen up to the point of
rupture. In some texts this property has been referred to as
toughness. It is used to evaluate materials that may be
subjected to heavy abuse or that might stall web transport
equipment in the event of a machine malfunction in end-use
applications. However, the rate of strain, specimen parameters,
and especially flaws may cause large variations in the results.
In that sense, caution is advised in utilizing TEB test results for
end-use design applications.
4.5 Materials that fail by tearing give anomalous data which
cannot be compared with those from normal failure.
5. Apparatus
5.1 Testing Machine—A testing machine of the constant
rate-of-crosshead-movement type and comprising essentially
the following:
5.1.1 Fixed Member—A fixed or essentially stationary
member carrying one grip.
5.1.2 Movable Member—A movable member carrying a
second grip.
5.1.3 Grips—A set of grips for holding the test specimen
between the fixed member and the movable member of the
testing machine; grips can be either the fixed or self-aligning
type. In either case, the gripping system must minimize both
slippage and uneven stress distribution.
5.1.3.1 Fixed grips are rigidly attached to the fixed and
movable members of the testing machine. When this type of
grip is used, care must be taken to ensure that the test specimen
is inserted and clamped so that the long axis of the test
specimen coincides with the direction of pull through the
center line of the grip assembly.
5.1.3.2 Self-aligning grips are attached to the fixed and
movable members of the testing machine in such a manner that
they will move freely into alignment as soon as a load is
applied so that the

塑料拉力機;塑料拉力機維修;塑料拉力機報價


環保在線 設計制作,未經允許翻錄必究 .? ? ? Copyright(C)?2021 http://m.hg1112.cn,All rights reserved.

以上信息由企業自行提供,信息內容的真實性、準確性和合法性由相關企業負責,環保在線對此不承擔任何保證責任。 溫馨提示:為規避購買風險,建議您在購買產品前務必確認供應商資質及產品質量。

會員登錄

×

請輸入賬號

請輸入密碼

=

請輸驗證碼

收藏該商鋪

登錄 后再收藏

提示

您的留言已提交成功!我們將在第一時間回復您~
国产老熟女激情小视频-成人一区二区人妻不卡视频| 青青操视频在线观看国产-欧美成人乱码在线观看| 亚洲精品蜜桃在线观看-国产欧美日韩在线观看精品观看| 日韩精品中文在线观看一区-亚洲bt欧美bt精品| 四虎成人在线免费视频-亚洲熟女中文字幕天堂| 亚洲区欧美区在线视频-亚洲碰碰人人AV熟女天堂| 黄片黄片在线免费观看-激情综合网激情五月俺也去| 亚洲欧美日韩国产一区二区三区-国产欧美日韩一区二区免费| 欧美日韩黑人在线播放-51在线精品免费视频观看| 久色高清精品在线国产-国产精品视频一区三区四区| 国产午夜精品理论片A级漫画-久久精品国产99亚洲精品| 婷婷人妻少妇激情在线-欧美日韩人体艺术一区二区| 国产欧美日本不卡精美视频-日本后入视频在线观看| 亚洲愉拍自拍欧美精品app-亚洲一区不卡在线视频| 91蜜桃传媒一二三区-日韩欧美国产一区呦呦| 亚洲欧美激情自拍色图-国产亚洲精品sese在线播放| 亚洲国产欧美日韩不卡-熟妇激情一区二区三区| 亚洲一区二区免费av-中文字幕人妻久久久一区二区三区| 亚洲一区二区少妇激情-国产精品美女久久高潮| 欧美一区二区三区调教视频-三上悠亚国产精品一区二区三区| 国产精品久久久精品一区-99久久免费精品国产男女性高好| hd在线观看一区二区-免费一区二区三区毛片在线| 国产剧情av中文字幕-五月婷婷在线手机视频| 99久热精品免费观看四虎-亚洲天堂精品视频在线| 99精品只有久久精品免费-蜜臀一区二区三区精品久久久| 欧美日韩国产综合新一区-国产综合av一区二区三区| av噜噜国产在线观看-欧美视频亚洲视频一区二区三区| 性色国产成人久久久精品二区三区-偷窥中国美女洗澡视频| 免费看黄色污污的网站-欧美一区二区三区爽爽| 久久久精品欧美日韩国产-欧美精品乱码视频在线| 中文字幕社区电影成人-欧美精美视频一区二区三区| 国产成人精品免费视频大全办公室-亚洲欧美日本综合在线| 亚洲视频一区二区三区免费-国产一级黄色大片在线| 国产精品一区二区欧美视频-国产一区二区三区天码| 日韩精品一区二区三区十八-日韩人妻少妇一区二区三区| 男人的天堂久久精品激情-最新亚洲精品a国产播放| 国产午夜精品理论片A级漫画-久久精品国产99亚洲精品| 亚洲最新国产无人区123-黄片一区二区在线观看| 91精品国产无线乱码在线-999精品视频免费看| 亚洲另类熟女国产精品-懂色一区二区三区在线播放| 日韩高清在线观看一区二区-美产av在线免费观看|