安全滑觸線在使用過程中加強維護保養非常重要，不少單位的滑觸線系統因失于維護而導致故障頻繁，影響正常生產。*，昂立電氣滑觸線是國內滑觸線行業的企業，昂立電氣滑觸線在國內多個領域市場占有比例遙遙。為了保證滑觸線正常運行，延長其使用壽命，其售后服務賈工程師根據多年經驗，提出了滑觸線日常維護與保養方面的看法：

Security sliding touch line in the use of the process to strengthen the maintenance is very important, sliding contact line system due to the loss of many units to maintain and lead to frequent failures, affecting the normal production. As everyone knows, Jieneng electrical sliding contact line is the sliding contact line industry leader, Jieneng electrical sliding contact line occupies more than in the domestic market share be way ahead. In order to ensure the normal operation of the sliding contact line, prolong the service life of the after sale service, Jia engineer based on years of experience, the sliding contact line daily maintenance and maintenance:

1.連接件：至少每年檢查一次。重點檢查緊固螺栓、焊縫及支撐件是否松動、銹蝕、移位等，發現問題及時處理。

1 connections: at least once a year to check. Focus on examination of the fastening bolts, welds and support is loose, corrosion, shift, found problems in a timely manner.

2.特別對行車軌道重合度、軌距、傾斜度等偏差較大、使用頻繁、車間粉塵過大、溫度較高及有水、酸、堿、霧和室外使用的環境，必須加強日常檢查與維護。

2 special on the running track of coincidence degree, gauge, inclination, deviation, frequent use, workshop dust is too large, high temperature and water, acid, alkali, fog and outdoor environment, must strengthen the routine inspection and maintenance.

3.安全滑觸線集電器：至少每季度檢查一次。重點檢查緊固件有無松動、移位及塑料件和活動件磨損情況，檢查彈簧拉力（集電器電刷與導軌的接觸應保持一定壓力（見下表）。發現問題及時處理。

The 3 Collector: at least quarterly check once a. Focus on examination of the fastener without loosening, displacement and plastic parts and moving parts wear, check the spring tension (collector brush and rail contact should maintain certain pressure (see table below). Found problems in a timely manner.

4.電刷：應根據移動用電設備使用情況每1—3個月檢查一次。重點檢查集電器電刷的磨損情況，若磨損量≥5mm時，必須更換。檢查時若發現電刷松動或發生磨損偏斜時，應查明原因，及時處理。

4 brush: electric equipment should be based on the use of every 1 - 3 months check once a. Focus on examination of the collector brush wear, if wear is greater than or equal to 5mm, must be replaced. If found loose or worn oblique brush examination, should identify the reasons, timely treatment.

5.日常檢查：重點檢查軌道的平直度有無明顯偏差（大于20mm）、錯位，絕緣保護件有無脫落、斷裂、破損，不銹鋼“v"型槽有無翹起；軌道上有無異物及導電粉塵等。必要時應檢測其絕緣電阻是否符合要求（相間絕緣電阻應≥10MΩ）。

5 daily inspection: inspection of rail straightness has no significant deviation (more than 20mm), dislocation, insulation protection piece off, fracture, damage, stainless steel "V" type groove is not tilted orbit; there is no foreign body and conductive dust etc.. When necessary, to detect the insulation resistance is required (interphase insulation resistance should be greater than or equal to 10M.).