簡要描述：多種氣體驅動：壓縮空氣、氮?dú)獾取?驅動輸入：0.3-0.69MPa壓縮空氣驅動就可獲得高壓輸出。自動保壓：工作時，迅速往復工作，隨著輸出壓力接近設定壓力值時泵的往復運動速度減慢直至停止，并保持這個壓力，此時消耗能量很小，無熱量產生，無零件運動。當壓力平衡打破后，氣動增壓泵自動開始工作到下一個平衡?！　〔馁|(zhì)優良：高壓部分材質為不銹鋼304或316。高壓柱塞材質為不銹鋼304或316，......

詳細介紹

詳細介紹

氣動增壓泵利用大面積活塞端的低壓氣體驅動而產生小面積活塞端的高壓流體。可用于壓縮空氣及其它氣體，輸出氣壓可通過驅動氣壓無級調節。

The pneumatic booster pump is driven by the low-pressure gas at the large area piston end to produce the high-pressure fluid at the small area piston end. It can be used for compressed air and other gases. The output air pressure can be steplessly adjusted by driving air pressure.

不同之處在于該系列泵是在FAT-A系列氣體增壓泵系列基礎上制造的雙頭泵，整臺增壓裝置全部采用鋁合金及不銹鋼制造。它的驅動活塞直徑為160mm，驅動氣壓≤8bar,兩端泵頭均帶有排氣冷卻。出廠時兩入口及兩出口可按用戶要求連接好管路。氣體輸入端有流量和氣體壓力的情況下，并且有要求出口壓力和流量同時的情況下可以選擇該款雙級單作用氣體增壓泵。The difference is that this series of pumps is a double head pump manufactured on the basis of fat-a series of gas booster pumps. The whole booster device is made of aluminum alloy and stainless steel. The diameter of its driving piston is 160mm, the driving air pressure is ≤ 8bar, and the pump heads at both ends are equipped with exhaust cooling.

The two-stage single acting gas booster pump can be selected when there is a certain flow and gas pressure at the gas input end and the outlet pressure and flow are required to be the same.

多種氣體驅動：壓縮空氣、氮?dú)獾取?nbsp;

驅動輸入：0.3-0.69MPa壓縮空氣驅動就可獲得高壓輸出。

自動保壓：工作時，迅速往復工作，隨著輸出壓力接近設定壓力值時泵的往復運動速度減慢直至停止，并保持這個壓力，此時消耗能量很小，無熱量產生，無零件運動。當壓力平衡打破后，氣動增壓泵自動開始工作到下一個平衡?！　〔馁|(zhì)優良：高壓部分材質為不銹鋼304或316。

高壓柱塞材質為不銹鋼304或316，并采用雙層密封。　　

Various gas drives: compressed air, nitrogen, etc.

Drive input: 0.3-0.69mpa compressed air drive can obtain high-pressure output.

Automatic pressure maintaining: when working, it works back and forth rapidly. As the output pressure approaches the set pressure value, the reciprocating speed of the pump slows down until it stops, and maintains this pressure. At this time, the energy consumption is very small, no heat is generated, and no parts move. When the pressure balance is broken, the pneumatic booster pump automatically starts to work to the next balance. Excellent material: the high pressure part is made of stainless steel 304 or 316.

The high-pressure plunger is made of stainless steel 304 or 316 and adopts double-layer seal.

維護簡單：氣動增壓泵的零件及密封少，維護簡單且成本低。相同系列泵的所有"O"型圈，維修包易損部件可相互替換，大大降低了維修成本。

　　1、保壓期間無消耗能量

2、具有防爆功能，無需電力或電線連接

3、結構小巧，重量輕，不受天氣變化影響

4、易實現自動控制

5、抗污染

6、輸出靜態壓力由驅動氣壓來五級調節

7、在滿負載時非常容易進行啟動、停止操作

8、易安裝，操作。

Simple maintenance: the pneumatic booster pump has few parts and seals, simple maintenance and low cost. All "O" rings and vulnerable parts of the maintenance kit of the same series of pumps can be replaced with each other, greatly reducing the maintenance cost.

No energy consumption during pressure maintaining
With explosion-proof function, no power or wire connection is required
Compact structure, light weight, not affected by weather changes
Easy to realize automatic control
Anti pollution
The output static pressure is regulated in five stages by the driving air pressure
It is very easy to start and stop at full load
Easy to install and operate.